PCB Relay G2RL. □ Coils Ratings for High-sensitivity Models. Note: The rated current and coil resistance are measured at a coil temperature of 23°C with a. Relays are most commonly used switching device in electronics. Let us learn how to use one in our circuits based on the requirement of our. SONGLE RELAY. RELAY ISO Simple relay magnetic circuit to meet low cost of mass production. 2. Datasheet pdf - osakeya.info

Author:TARA SELSER
Language:English, Spanish, French
Country:India
Genre:Environment
Pages:118
Published (Last):17.03.2016
ISBN:906-3-31678-457-9
Distribution:Free* [*Registration Required]
Uploaded by: OFELIA

56984 downloads 113226 Views 29.75MB PDF Size Report


Relay Datasheet Pdf

With over 30 years experience at the forefront of relay innovation and .. and other critical values, please refer to the respective data sheet. In case of doubt. V 10A RELAY MODULE. Description. The relay module is an electrically operated switch that allows you to turn on or off a circuit using voltage . (osakeya.info) America or its affiliates do not warrant that the content of datasheet is error free.

How to use a Relay Relays are most commonly used switching device in electronics. Let us learn how to use one in our circuits based on the requirement of our project. Before we proceed with the circuit to drive the relay we have to consider two important parameter of the relay. Our relay here has 5V trigger voltage, but you can also find relays of values 3V, 6V and even 12V so select one based on the available voltage in your project. Make sure the load you are using falls into this range. The above circuit shows a bare-minimum concept for a relay to operate. This switch can be anything from a small transistor to a microcontroller or a microprocessor which can perform switching operating. You can also notice a diode connected across the coil of the relay, this diode is called the Fly back Diode. The purpose of the diode is to protect the switch from high voltage spike that can produced by the relay coil.

Please check your product under actual service conditions before use.

Ir2153 schematic

If you continue to use a product in a poor condition, items with deteriorated insulation performance may generate abnormal heat or smoke or even ignite.

The product's failure or end of service life may cause accidents involving risks to human health, fire, or danger to the public at large.

We advise you to apply safety measures and regular maintenance work, such as the use of redundant design, fireproofing, and malfunction-preventing design , to rule out such accidents. We classify product quality levels by product applications into "standard level," "special level" and "specific level.

Each quality level is defined for products for use in specific applications as listed below.

If you intend to use our products without agreeing product specifications and applications with us, we cannot guarantee the quality of the products in the following cases. Please contact our sales representatives before using the products to confirm product specification and applications. In the above case of 1 , using the product for a different model with different service conditions after receiving the product specifications.

Please perform receiving inspection, such as verifying box es , parts and checking documents attached to delivered items, as soon as you receive parts to your sites. We also highly recommend to keep received parts at well controlled locations to avoid damages of some sort.

D series, instantaneous power relays

The warranty period of products listed on this site shall be one year from the date of download or delivery of the products to your designated location unless our company and the customer agree otherwise. If you should find during the warranty period that the product has a defect or flaw for which we are responsible, we will immediately replace the defective product to part with a non-defective one or repair the defective part without charge at the location of download or delivery of the product.

However, if the cause of such a defect or flaw is identified as due to any one of the following causes, the above warranty coverage shall not apply. The other end of the load is either connected to NO or NC. If connected to NC the load remains connected before trigger. Normally Open NO.

If connected to NO the load remains disconnected before trigger.

Omega Engineering | Shop for Sensing, Monitoring and Control Solutions with Technical Expertise

Relays are most commonly used switching device in electronics. Let us learn how to use one in our circuits based on the requirement of our project. Before we proceed with the circuit to drive the relay we have to consider two important parameter of the relay. Our relay here has 5V trigger voltage, but you can also find relays of values 3V, 6V and even 12V so select one based on the available voltage in your project.

Make sure the load you are using falls into this range. The above circuit shows a bare-minimum concept for a relay to operate. This switch can be anything from a small transistor to a microcontroller or a microprocessor which can perform switching operating. You can also notice a diode connected across the coil of the relay, this diode is called the Fly back Diode.

TOP Related


Copyright © 2019 osakeya.info. All rights reserved.
DMCA |Contact Us